VERTEXWater ProductsPureWaterCoolerWater DispenserOWNERS INSTALLATIONMANUAL™VERTEX WATER PRODUCTS ModelsPWC3000/2000/6003 Temp - Room, Hot, ColdPWC100
3.4 Feed Water ConnectionsTo connect the feedwater, use the supplied self-piercing saddle valve to connectto the cold water supply line under the sink
The standard tubing connections on the PureWaterCooler™ are of quick-con-nect o-ring seal design. Use the tubing and follow the instructions below in
– 10 –4.0 Operation4.1 Start-UpRemove front cover by depressing lock tabs on front panel (see fig.1) and pullingforward. With the front cover off, tur
4.3 Power Controls, Cold Water FunctionWith the water level indicator showing the main tank full,start operation by producing cold water first. Drain
5.0 Model 1000 and 1010 Description5.1 Model 1000 and 1010The Model 1000 provides water at 2-temperatures , dispensed from two spigots,“hot” and “cold
– 13 –5.4 Start-Up FlushOpen lower front door to access filter assembly, turn the water on at thepiercing valve. This brings water to the ball valve.
– 14 –5.5 Tank FlushFlush tanks out by draining all water through the (1) drain plug located on theback of the cooler. Let the tanks fill again with t
– 15 –6.0 Other Models6.1 Model 500This is a countertop version of the Model 1000, a 2-temperature cooler previouslydescribed in section 5.0. It does
– 16 –7.0 OptionsOptions/Accessories to the cooler are described below.7.1 UV StageAn additional stage after the filters is available for all models.
– 17 –f) Place new filters in the plastic holding clips. Make the tubing connections intothe fittings. BUT DO NOT CONNECT THE OUTLET TUBING OF THE2ND
WARNING1) Installing this cooler in an area were water may cause severe or costly dam-age is not recommended. If Installation of this cooler is in an
9.0 Cleaning and MaintenanceThese instructions apply tto the model 2000, 3000 and 600 specifically, but canbe applied to other models. 9.4 SanitizeFil
10.0 Trouble ShootingNote - In the event of problems beyond the scope of the troubleshooting described in themanual, please call your selling dealer.
– 20 –11.0 SpecificationsModel No.Voltage/FrequencyDimensionsWeight (empty)Room Temperature TankHot Water Tank CapacityCold Water tank CapacityPower C
12.0 WarrantyWarrantyThe VERTEX PureWaterCooler, is warranted to be free from defects inmaterials and workmanship under normal use within the conditio
VERTEX WATER PRODUCTS, Montclair, Calif.PWCM-1 Rev B.1 • 5/07 Copyright 2007VERTEX Industrials, Inc.
Table of Contents1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 22.0 Receiving . . .
1.0 INTRODUCTIONThe VERTEX Pure Water Cooler products are a means to produce and dispensegood-tasting, safe water without using “bottles of stored wat
2.0 RECEIVING THE COOLER2.1 Unpacking (All Models)The PureWaterCooler™ is shipped completely assembled and ready to operate.Remove the top of the box
The internal flow of water to the tanks and dispensers is shown in Figure 2. Thearrangement of the water filter system in the bottom of the cabinet is
– 5–Figure 2Flow Schematic (Model 2000 & 3000)VentFloat TypeWater Level ControlMain Water TankCold TankElectric HeatingCoil Inside TankCheck Valve
3.2 Positioning the CoolerThere are some precautions in locating and using the PureWaterCooler™. Seethe items in Figure 4 below. In addition, the cool
– 7 –3.3 Cooler Water Connections(See Fig.5) When received, the water connections on the back have color codedtube sections with red shipping plugs in
Commentaires sur ces manuels